Remote Control Auto Alarm System PDF Installation Instruction Manual

Locate the wire under the driver’s kick panel. Use the voltmeter connecting to ground, verify that you have to correct wire with the doorsunlocked, the voltmeter will receive “12 volt”. Lock the doors and the voltmeter will read “0 volt”. Move the alligator clip to +12V and the voltmeter will receive “12 volt”. Cut this wire and make connections. Be sure to program door lock timer to
3 seconds.(See Feuture II – 1 Programming.)

A. PROGRAMMING TRANSMITTER:
1. Turn the Ignition switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and hold it until a long chirp is hearing then release the valet switch. You are now in the Transmitter programming mode.
Program:
1. Press button on the transmitter until the siren responds with a confirming chirp the first transmitter is now programmed.
2. Press button on the second transmitter until the siren responds with a confirming chirp, the second transmitter is now programmed.
3. Apply the same procedure to program 3rd and 4th
Exit: Turn Ignition to ‘OFF’ position, or leave it for 15 seconds. A 3 long chirps to confirm exit.
Note: If more than 4 transmitters programmed, the system only kept the last 4 transmitters.

B. ALARM FEATURES PROGRAMMING:
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times and hold it until one chirp and a long chirp is hearing then release the valet switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
a. The siren chirps and LED pause will indicate latest setting.
b. The factory default settings is always [1] LED flash, [1] chirp.
4 Depress the transmitter button ‘A’ to change the feature. Simple redepressing the transmitter button ‘A’ again until the module advances to your desired setting.
a. In this case, Press button ‘A’ again, the module would advance to [2] LED flash, [2] chirp. Press button ‘A’ again, the module would advance to [3] LED flash, [3] chirps etc.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.

SILENT ARMING / DISARMING: Press the + button together on the transmitter will arm or disarm your security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicle’s parking light only.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Press the button on the transmitter twice within 3 seconds will arm the security system, by-pass the shock sensor and the optional sensor connected to 4 pin plug. The system will chirp one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to normal operation during the next arming cycle.
G. PASSIVE ARMING: (See Feature “II – 2” Programming) Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.

1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood / trunk, the security system LED will stop flashing. It will begin flashing again once the vehicle all entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time.
- PASSIVE DOOR LOCKING: (See Feature “II 2” Programming)
The vehicle’s door will automatically lock after passive arming cycle has been completed.

Download Remote Control Auto Alarm System PDF Installation Instruction Manual