The vehicle shall be entitled to request a new vehicle if it is the state between the above. He / she has a new vehicle as replacement. The Lemon Law in Wisconsin was first activated in 1983 and is still the best source for the vehicle owner in Wisconsin.

You can download Lemon Law in Wisconsin in Summary PDF format here.

Post from: Free Download Automotive PDF Manual

Lemon Law in Wisconsin Summary PDF Reference

Be careful that exhaust is supported when removing isolators. Then remove metal muffler hanger bracket(s) from frame by removing nuts holding them to bottom of frame. Return metal hanger bracket(s), bolt(s) and nut(s) to owner. Remove existing 6mm nuts holding muffler heat shield(s) to bottom of Hyundai Sonata vehicle. (4) per heat shield. See next page for heat shield trimming. Shield(s) will be trimmed and replaced after installing fasteners but before installing hitch.

Using bolt-leaders fish-wire 3/8”-16 x 1-1/4” carriage bolts and carriage blocks through 7/8” diameter holes in bottom of frame on both sides of vehicle and pull down through 3/4” diameter holes in bottom of frame toward rear of vehicle. Now using bolt-leaders fish-wire 3/8”-16 x 1” carriage bolts and carriage blocks up through 7/8” diameter holes and back down through same hole both sides of vehicle. Now trim muffler heat shield(s) before raising hitch into position. See pictures on next page for detail on how to trim muffler heat shield(s). After trimming shield(s) re-install them on vehicle before mounting hitch to Hyundai vehicle.

Raise hitch into position and install conical toothed washers and nuts on bolts installed in Step 1. Be careful not to push bolts back up into frame. Insert flat washers as needed on rear attachments between hitch and frame to take up space. On dual tailpipe vehicles it may be necessary to push hitch towards the passenger side as far as possible so that hitch bracket is up against vehicle trunk pan. This allows more clearance for exhaust on Driver’s side. Torque fasteners to specifications below.

Download Hyundai Sonata GLS Limited Dual Exhaust PDF Installation Instructions

Post from: Free Download Automotive PDF Manual

Hyundai Sonata GLS Limited Dual Exhaust PDF Installation Instructions

Remove the six push pins and six phillips head screws from black plastic on the top side of fascia and set aside. Using the 10MM socket, remove two metric bolts from head light assembly, pull forward, unplug electrical and set aside, both sides. Just under headlight assembly, remove one push pin on fascia, both sides. Remove one metric bolt behind assembly with the 10MM socket, both sides.

Remove two metric bolts from top side of fascia with the 10MM socket. Using the 8MM socket, remove one metric bolt from upper fascia corner, just forward of front tires, both sides. Using the Phillips screw driver, remove two screws from upper fascia’s opening, behind license plate.

Download Kia Optima 2001-2002 BX2706 PDF Installation Instructions Manual

Post from: Free Download Automotive PDF Manual

Kia Optima 2001-2002 BX2706 PDF Installation Instructions Manual

The program allows them to gather feedback that will be used to further improve the plug-in technology. The company also hopes the demo models will spur development of public access charging stations available in such technically-advanced cities as Boulder, Colorado and even Austin, Texas. Starting with tests in Boulder in the fall of 2009 and spreading to include parts of California, NY, New Jersey, Washington D.C., Portland, Oregon, Pittsburgh, Pennsylvania, Texas and other areas, the dashboard data from these test vehicles to help consumers understand how the plug-in hybrid vehicles are being used.

The Prius Plug-in Hybrid is basically built just like the other Prius models, a mid-size box that seats five but with a much heavier lithium-ion battery pack that can be charged in three hours on a 110-volt outlet, or in half that time using a 220 volt outlet. The charge will get you 13 miles, then the car reverts back to hybrid or…

Download Toyota Prius 2012 Plug-in Hybrid PDF Reference Manual

Post from: Free Download Automotive PDF Manual

Toyota Prius 2012 Plug-in Hybrid PDF Reference Manual

Tools Needed: 10mm nut driver or socket, #1 Phillips screwdriver, and Trim Removal Tools (Optional) Be advised: These instructions may not include specifics for all vehicle configurations.
1. Set Parking brake and adjust steering wheel to various settings to facilitate removing the Instrument panel.
2. Partially remove the driver’s side kick panel.
a. Using your hands, gently pull straight back on the kick panel. There are 2 release clips; one is shown below. The other clip is directly below the one shown.

3. Remove the coin tray.
a. There are 4 clips that hold the tray in place. Gently pull straight out from the dash to remove the tray
4. Remove the driver’s side, lower instrument panel.
a. Using a 10mm socket, remove the two bolts shown in the following photos.
b. It’s not necessary, but it makes room to pull the door seal out and away from the instrument panel. This allows room to get your fingers or trim removal tool behind the panels.
c. Starting on the lower left-hand side, gently separate the lower instrument panel by pulling straight out from the dash.
i. When it’s completely separated, lower it to the floorboard.
d. Remove the Instrument Panel bezel.
i. Using a #1 Phillips screwdriver, remove the screws shown in the photo below. Note: make sure that good contact between the screwdriver and screw is made to ensure that the head is not stripped.
ii. It is a good idea to place some thick card-stock or paper around the top of the steering column to prevent scratching.
iii. Starting on the left-hand side, gently separate the upper Instrument Panel Bezel.
1. Rotate it up and to the left and let it hang.
e. Remove the Instrument Panel Cluster
i. Using a 10mm socket, remove the (4) retaining screws.
ii. Disconnect the IPC connector from the cluster.
Note: To prevent breaking the connectors, DO NOT rock the connector back and forth. Squeeze the release and pull straight up.
1. Using your index finger, you will be able to feel the locking tab on the back of the connector. Press-in on the tab and remove the connector
f. Using the supplied cable, connect the small black connector (C3) to the VSS inline module.

5. Connect (C2) of the supplied cable to (P2) on the green interface board.
6. Connect the vehicle’s IPC connector to (P1) of the green interface circuit board.
7. Carefully stow away the inline module and the green interface board.
a. Both pieces can be tied to a brace, cable or support, using tie wraps.

b. Connect the other end, marked (C1), of the supplied cable to the Instrument Panel Cluster.
8. Reverse the process of this document to properly re-install the Instrument Panel components.

Download Toyota Tacoma Hypertech Inline Speedometer Calibrator Module PDF Installation Instructions

Post from: Free Download Automotive PDF Manual

Toyota Tacoma Hypertech Inline Speedometer Calibrator Module PDF Installation Instructions

INTERIOR TECHNOLOGY. 1 PARKVIEW REAR BACK-UP CAMERA.[1] An available camera on Journey’s liftgate displays a rearview video image on the radio screen while vehicle is in reverse, providing the driver with additional rearward visibility. [2] 2 MYGIG. The available MyGIG Multimedia Infotainment System with Navigation[3] bundles entertainment, information, and [4] communication. It combines navigation with real-time traffic updates via SIRIUS® Satellite Radio. When MyGIG is paired with ® the UConnect Hands-Free Communication System, you can change radio stations, orde r up digital audio files, and input destination information through voice activation in three languages: English, French, and Spanish. There’s also a 30GB hard drive for storing photos and upwards of 4,100 digital music files, playlists, maps, points of interest, and more. The 7-inch LCD monitor with full-color enhanced graphics uses a joystick to surf seamlessly through MyGIG functions. The also-available touch-screen MyGIG Multimedia Entertainment System[2] provides all the same great features but without the navigation and joystick function. PREMIUM SOUND SYSTEM. Opt for the 6 ?Infinity® premium speakers, subwoofer, and 368-watt amplifier.

[1] Always check entire surroundings before backing up. the SIRIUS dog logo are registered trademarks of SIRIUS Satellite Radio Inc. All other trademarks, service marks and logos are the property of their respective owners. For full terms and conditions, visit sirius.com. Prices and programming are subject to change. Not available in AK and HI.

[2] MyGIG in-dash DVD capability is not available in all states. See your dealer for details. FIVE-PASSENGER SEATING WITH AVAILABLE THIRD ROW. Journey’s interior starts with standard five-passenger seating, featuring 40/60 split fold-flat stadium-style second-row seats with fore/aft adjustment and an available power six-way driver’s seat. Leather-trimmed seats are standard on R/T models while SXT models sport class[1]-exclusive YES Essentials®[2] stain resistant, odor resistant, antistatic seat fabric for easy cleaning. All seats, even the second row, recline. AVAILABLE THIRD-ROW SEATS. Choose Journey’s available third row for seating two additional passengers. The 50/50 split fold-flat rear seats recline six degrees for added relaxation. TILT ’N SLIDE.TM Thanks to available Tilt ’n Slide second-row seats and rear doors that open 90 degrees, Journey has one of the easiest rear entries. The seats move easily to accommodate entry to the available third-row seats. REAR CARGO AREA. The standard tri-fold load floor behind the second-row seat gives five-passenger models an extra 4.2 cu ft of added utility. The load floor converts to “grocery bag mode,” to keep your eggs from scrambling before you reach your driveway. Dig a little deeper on any Journey model and you’ll find another level in the cargo bin that conceals the jack, jack tools, nd spare tire winch. Based on Ward’s 2008 Large Cross/Utility Vehicle segment. [2]Not compatible with aftermarket fabric-protecting coatings.

Download Dodge Journey 2011 SUV Car PDF Technical Specification Manual

Post from: Free Download Automotive PDF Manual

Dodge Journey 2011 SUV Car PDF Technical Specification Manual

Step 6: Set cover assembly on front bulkhead
Step 7: – Place side rails on truck bed rails. – Assemble rear clamps as shown. This will hold side rails in place. – Insert side rail corner plugs in front header.
Step 8: Place remaining clamps. notice: Each clamp assembly, starting at the front then to back, has a special groove alignment. See detail 8a, 8b,and 8c.

Step 9: Align cover with pickup bed
Step 10: Tighten front clamps
Step 11: Tighten Center Clamps
Step 12: Leave 1/8” clearance between tailgate header and side rails.
Step 13: Tighten rear clamps: reinstall cargo cleats and rear plugs.
Step 14: Install weather seal on tailgate corner plugs: Corner plug
Step 15: Close Cover: Release safety straps, and unroll cover over pickup bed. Open tailgate. With tailgate open, hook tailgate header into header stops on both sides of vehicle. Rotate tailgate header down until both latches engage. Listen for double click. Secure loop to hook fasteners on one side rail by pressing edge of cover along full length of rail.

Tools Required:
1/2” Socket
3/8” Drive Ratchet
Scissor

Download Toyota Tacoma Truxport PDF Owner and Installation Manual

Post from: Free Download Automotive PDF Manual

Toyota Tacoma Truxport PDF Owner and Installation Manual

Installation
1. Secure the Relays to the next to the Battery with wire ties (see Picture 1)
2. Attach a T-Tap to the high beam (see note) wire. Attach a T-Tap to the low beam wire
3. Attach the switch relay’s white wire to the high beam T-Tap and blue wire to low beam T-Tap
4. Attach the 2 black wires from each relay to ground
5. Attach fog light relay’s red wire to the positive terminal + of the battery
6. Install split loom tube over long wires from relays to fire wall. Locate the large vehicle harness grommet on the left side. Cut the auxiliary grommet and push both wires through wiring access nipple off the
7. Run the split loom tube with all wires on the driver side of the car. Use 8″ wire ties as needed
8. From inside the cabin locate the switch wires that were pushed through in step 6
9. Mount switch into switch knockout of dash
10. Install switch harness
11. Attach ground (black) wire to ground
12. Connect the white wire of switch harness to the white wire of fog light harness
13. Connect the red wire of switch harness to red wire.
14. Reinstall dash panels
15. Route the fog light wire under car.
16. Remove fog light cover plates and lower splash shields
17. Mount both fog lights into bumper.
18. Snap on both fog light bezels
19. Plug in left side fog light into harness plug
20. Run right fog light wire harness and secure with wire ties
21. Reattach the lower splash shields

Check System for Operation
1. Reconnect battery negative terminal
2. Turn on headlamp low beams, then press fog light switch to “ON” position. Fog lights should be working. Fog lights will only work when the low beam headlamps are “ON”. Fog lights will NOT work when the high beam headlamps are “ON”

Download Toyota Camry 2010 Fog Light Kit PDF Installation Instructions Manual

Post from: Free Download Automotive PDF Manual

Toyota Camry 2010 Fog Light Kit PDF Installation Instructions Manual