Congratulations on the Purchase of your new TOY-SCl SiriusConnect Interface! Your TOY-SCl is designed to be compatible with select vehicles that support Satellite Radio operation (requires additional purchase of & connection to a SiriusConnect tuner or dock!. Your interface is designed to replace the factory satellite tuner in your Toyota, Lexus or Scion vehicle. It is also compatible with systems that do not have the factory satellite tuner installed. For the latest information about this and other SIRIUS products and accessories.
The GM2L-POD/S allows you to operate your iPod (Mini, G3, G4, G5) using the OEM satellite radio controls of your LAN BUS or ClassII Satellite-ready GM Group radio. Using this interface, the iPod will emulate the factory XM Satellite system, providing you with one of the most interactive OEM iPod “INTERFACES” in the industry.
Please follow the safety instructions and apply the handbrake. Switch on the ignition. Do not start the engine! Press and hold the two outside buttons I + III – releasing only when the diode begins to flash after approximately 20 seconds. This procedure erases the factory-set default codes and does not have to be followed to program additional remote controls. Press the appropriate HomeLink button I, II or III which you want to program and keep holding it until the diode starts flashing slowly. You will now have 5 minutes to copy the signal from your remote control onto the HomeLink transmitter unit.
Before You Start
For the initial setup of the Honda Teradyne GNA600, the latest version of HDS software must be installed on the host PC. We strongly recommend using the USB PC Interface Cable (TDS35525406) as your wired connection to the GNA600. The correct device drivers for the USB PC Interface Cable are included with the HDS software. If an Ethernet cable is used for your wired connection, you will need to do extra steps. NOTE – Setup of the GNA600 connection is fully automatic if you have the correct drivers from the HDS software installed, use the USB PC Interface Cable, and carefully follow the set up instructions. If you use an Ethernet cable, you must do a manual setup of the GNA600 connection (see section 5.4).
DiCE – Diagnostic Communication Equipment, is a tool that is used together with VIDA All-in-one to communicate with the vehicle. Communication makes diagnosing and troubleshooting the vehicle possible, as well as the downloading of software. DiCE uses Bluetooth to transfer information wirelessly between the vehicle and VIDA All-in-one. This gives the mechanics more flexibility. An USB cable can be used as an alternative to Bluetooth. DiCE has an integrated CARB cable, which is connected to the vehicle’s diagnostic socket. When connecting to the vehicle, DiCE is powered as long as the battery is charged. DiCE has a folding hook that is designed for hanging the unit from one of the grab handles in the
vehicle for example. When DiCE hangs visibly, Bluetooth reception is optimized and it is also visible to the mechanic.
Rotate the upper frame away from the lower frame. To move the frames, pull and turn both red triggers on the outer hubs. Position the frames. Find your measurement in the fit sheet. See fitting your car (above). • You will need a measuring tape. • On a flat surface, move the frames apart. • With the pads flat, measure from the inside edges of the tubes. Upper frame • with triggers out, adjust upper frame until it rests on the vehicle. • The position is relative to the lower frame and will depend on vehicle shape.
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Shop towel
Isopropyl alcohol
Diagonal cutters
Utility Knife
Ratchet
10 mm Socket
File
Felt-tip pen
Masking tape
Plastic trim tool
T/N SILTRIMTL 10
Scissors
Steel wire
Rubber mallet
Needle nose pliers
Torx wrench
Scale
PLAYING A DIGITAL VIDEO DISC
The DVD player plays DVD videos, video CDs and audio CDs. To play a DVD, begin by placing the ignition switch in the ACC or ON position and pressing the POWER button. Insert the disc into the slot. The disc is automatically drawn in. The player can be operated by using the control panel buttons or the remote control. The DVD player can be operated by pressing the CD •DVD button. Press the REAR ON •OFF button to
toggle the rear audio control on and off. Press the CD •DVD button to toggle between the CD and DVD operation.
